MTC400 on a lift frame, in the high position
MTC400 on a lift frame, in the low position
Close-up of the 38 mm slats on the lift frame
Close-up of the wired remote
MTC400 with lift frame and side rail
MTC400 with lift frame, side rails, headboard and footboard

Adjustable bed with lift frame MTC400

The five-section MTC400 on a lift frame. Two motors and a single remote to adjust the bed and set its height.

  • 5adjustable sections
  • 2motors, one remote
  • 43-71cmadjustable lift frame height
  • 4/5slat tilt
  • 3 years motor warranty
  • Made in Granollers (Spain)
  • Compatible with lift frame

Full specifications

Frame
60×20 mm iron tube on the outer perimeter and on the cross bars where the round legs are fitted.
Articulation
30×30 mm tube joined with polyamide joints, motorized in 5 sections (4 optional).
Motors
Dual: one built into the bed base and a linear motor for vertical lift in the frame. 3-year warranty.
Remote
A single wired remote for the bed base articulation and the lift frame.
Adjustable height
From 43 to 71 cm in 80 and 90 cm widths; from 47 to 75 cm in 105 cm.
Slats
Natural beech plywood, 38 mm, flexible, gray melamine finish.
Lumbar zone
Twice as many slats. Firmness adjustable with the firmness adjusters: outward for firmer, inward for softer.
Slat fixing
PELD plastic slat holders, solid and silent, fixed to the inner frame.
Tilt
4/5.
Maximum weight
100 kg.
Options
Side rails, matching headboard and footboard. The headboard and footboard must be ordered with the bed.
Ordering
Best ordered with the bed: the motor of a standard adjustable bed base is not compatible with the lift frame motor and would have to be replaced.
Warranty
3 years.

Five sections that move independently

Head, upper body, thigh and leg sections move around the seat section, which stays fixed. The same wired remote adjusts the bed and raises or lowers the lift frame. Also available with 4 sections to order.

The 5 sections, seen from the side

  1. Head1
  2. Back2
  3. Seat3
  4. Thigh4
  5. Legs5

The seat section (3) is fixed; the others move up and down.

  • Relax

    Upper body and knees raised. For reading, watching TV or resting without lying fully flat.

  • Circulation

    Legs above the upper body, with the back almost flat.

  • Sitting up

    Upper body almost upright: helps the user sit up and get out of bed.

  • Full elevation

    Head and legs raised at the same time, using the full motor stroke.

A lumbar zone with firmness on demand

Where the hips rest, the MTC400 has twice as many slats. With the firmness adjusters outward the zone is firmer; inward, softer.

  • 38 mm beech slats
  • Firmness adjusters
Lumbar zone: double slats
HeadFeet

The whole bed at the height you need

Designed for care settings and home care.

MTC400 with lift frame in the low positionMTC400 with lift frame in the high position

Lift frame

Raises the bed vertically. Lower for getting into bed safely; higher so the caregiver can work without straining their back.

71 cmheight from the floor to the bed base
WidthLowHigh
80 and 90 cm43 cm71 cm
105 cm47 cm75 cm
  • Gray melamine headboard and footboard

    Headboard and footboard

    Matching the bed. Ordered with the bed.

  • Side rail

    Side rails

    Metal side rails, for added safety.

Adjustable bed comparison

MTC400 with lift frameThis modelA400 with lift frameMTC400
Sections5 (4 optional)45 (4 optional)
Slat38 mm, double in the lumbar zone120 mm38 mm, double in the lumbar zone
Motors2: bed base and lift frame2: bed base and lift frame1
RemoteOne, wiredOne, wiredWireless
Height with lift frame (80 and 90 cm)43 to 71 cm41 to 69 cmWithout lift frame
Height with lift frame (105 cm)47 to 75 cm45 to 73 cmWithout lift frame
Tilt

We'll email it to you

Leave your email and we'll send you the download link. If you run a shop, we'll also tell you about our trade terms.