MTC400 with legs, adjusted to the relax position
Close-up of the beech slats and the wireless remote
MTC400 on a lift frame, in the low position
MTC400 on a lift frame, in the high position
MTC400 with lift frame, side rails, headboard and footboard

Electric adjustable bed MTC400

The most complete adjustable bed in the range. Five motorized sections, twice as many slats in the lumbar zone and firmness that adjusts to each user.

  • 5adjustable sections
  • 6.500Nmotor with wireless remote
  • 4/5slat tilt
  • 8cmbed base height
  • 3 años de garantía en el motor
  • Made in Granollers (Spain)
  • Compatible with lift frame

Full specifications

Frame
60×20 mm iron tube on the outer perimeter and on the cross bars where the round legs are fitted.
Bed base height
8 cm.
Articulation
30×30 mm tube joined with polyamide joints, motorized in 5 sections (4 optional).
Motor
6,500 N with wireless remote. 3-year warranty.
Slats
Natural beech plywood, 38 mm, in blocks of two, gray melamine finish.
Lumbar zone
Twice as many slats. Firmness adjustable with the firmness adjusters: outward for firmer, inward for softer.
Slat fixing
PELD plastic slat holders, solid and silent, fixed to the inner frame.
Tilt
4/5.
Twin frame
From 110 cm wide, with a single motor.

Five sections that move independently

Head, upper body, thigh and leg sections move around the seat section, which stays fixed. All with a single wireless remote. Also available with 4 sections to order.

The 5 sections, seen from the side

  1. Head1
  2. Back2
  3. Seat3
  4. Thigh4
  5. Legs5

The seat section (3) is fixed; the others move up and down.

  • Relax

    Upper body and knees raised. For reading, watching TV or resting without lying fully flat.

  • Circulation

    Legs above the upper body, with the back almost flat.

  • Sitting up

    Upper body almost upright: helps the user sit up and get out of bed.

  • Full elevation

    Head and legs raised at the same time, using the full motor stroke.

A lumbar zone with firmness on demand

Where the hips rest, the MTC400 has twice as many slats. Each pair has two firmness adjusters that slide by hand: outward makes the zone firmer, inward makes it softer.

  • 38 mm beech slats in blocks of two
  • Firmness adjusters
Lumbar zone: double slats
HeadFeet

From bedroom bed to care bed

The same bed adapts as the user's needs change.

MTC400 with lift frame in the low positionMTC400 with lift frame in the high position

Lift frame

Raises and lowers the whole bed with the same remote. Lower for getting into bed safely; higher so the caregiver can work without straining their back.

71 cmheight from the floor to the bed base
WidthLowHigh
80 and 90 cm43 cm71 cm
105 cm47 cm75 cm
  • Gray melamine headboard and footboard

    Headboard and footboard

    In gray melamine, matching the bed and the lift frame.

  • Side rail

    Side rails

    Metal side rails, sold in pairs.

  • Set of legs with casters

    Legs

    Round, 27 cm, height-adjustable or with casters.

Adjustable bed comparison

MTC400This modelA400C400
Sections5 (4 optional)45 (4 optional)
Slat38 mm in blocks of two120 mm53 mm
Lumbar zoneDouble slat, adjustable firmness-2 slats of 118 mm
Tilt
Bed base height8 cm7 cm7 cm
Lift frameYesYesYes

We'll email it to you

Leave your email and we'll send you the download link. If you run a shop, we'll also tell you about our trade terms.